Be sure that the paper does not exceed the maximum stack height mark in the input tray. THANK YOU!!! - Anonymous Thank you, Thank you, Thank you! - Anonymous Sure as @#$\% there was a corner of a piece of paper stuck behind the bottom sensor. Se podrá valorar cuando se haya alquilado el vídeo. Video Photos Link Add Upload Upload × × Draw a box over the problem!! this content
Figure 14: Close upper rear door If no paper is visible, open the lower rear door (rear output bin). After 2 hours of 13.20.00 front paper jam errors looking for anything I discovered the problem. bit of paper is inside. Finall i grabbed an old fuser I was keeping for rolling parts...(just in case) and put in in. http://www.fixyourownprinter.com/posts/35152
we removed the major portion of it. Faulty secondary transfer engagementsensor. Figure 23: Pull up on blue latches Pull the fuser out of the printer. What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account?
Will the printer work without these springs? Figure 10: Replace trays Press (Select) to resume printing. Disconnect the paper feeder pickup solenoid connector J4002 from the paper feeder. Try printing from all available input trays to identify whether the problem is isolated to one tray.
If the problem is not resolved continue with the following paper jam sections below. Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete. When you get the error and lift and close the top cover, the engine will then turn and the message will come back.
Browse Categories Answer Questions HP Color LaserJet 3500 Printer HP LaserJet Printer and Copier HP Printer and Copier Printers & Copiers All Unanswered Join Sign In Ask a Question × HomeForumPrinters
by Stephen on Mar 3, 2006 at 8:07am Add comment Please sign in to comment 0 That would be the notorious 13.20 jam message and here is one solution I have All images and logos used with permission from the respective owners. Measure the resistance between the connector J1016-6(CSTSL) andJ1016-5 (+24VA). HP Color LaserJet 1500/2500, 2500n printer repair | HP Color 1500/2500 service HP Color LaserJet 2550,2550n printer repair | HP Color 2550/2550n service HP Color LaserJet 2600/2605 printer repair | HP
Figure 15: Open lower rear door Press down on the green levers and remove the paper. http://www.fixya.com/support/t15115744-hp_color_laserjet_3500_error_code We do not sell these spare parts.We help you to create your parts sheets to request from your suppliers. Wait 10 minutes before proceeding. top Provide feedback Please rate the information on this page to help us improve our content.
I've been able to see pieces of paper jammed up in there. news Restore password × Upload manual upload from disk upload from url Thank you for your help! Elige tu idioma. Figure 45: Replace Tray 2 Press (Select) to resume printing.
This was a front door jam. Replace the magenta and yellow print cartridges. Try at least two times Open the rear cover behind the fuser to allow paper to exit out the back. have a peek at these guys Tell us some more!
Figure 8: Remove paper If the paper is not visible, check inside the printer in the top of the tray opening. When it gives you a “jam in tray 2” pull the tray out and you will notice the paper is pushed forward out toward the front of the printer instead of Figure 2: Remove paper from tray Grasp the jammed paper by both corners and pull.
Remove any excess paper from the input tray. If you cannot get to it from link. See if one side sticks out more than the other. I have been using this printer for years and never had an issue.I'm printing small envelopes and one fell loose right before the fuser cartridge.
Don't replace: rejuvenate! by Anonymous on Jul 19, 2007 at 1:22pm Add comment Please sign in to comment 0 DMZCompute's fix worked for me. Hold the fuser with thumbs on the blue ridges and fingers on the blue latches. http://isker.org/hp-color/hp-color-laserjet-3500-error-code.html Vuelve a intentarlo más tarde.
HP Color LaserJet printer repair/service in Los Angeles, Orange County and Riverside! Cargando... Press to highlight configure device. 3. Acción en curso...
Dedicated paper sensors detect whether paper is present in the sensor and if paper is fed normally. Adjust input tray guides so they hold paper firmly in place without bending it. Do not touch the top of the transfer unit or the contacts on the left side of the transfer unit. Figure 6: Remove Tray 3 If the paper is not visible, check inside the printer in the top of the tray opening.
It's a bit more effective and slides a bit easier.
© Copyright 2017 isker.org. All rights reserved.